DPI705E@2023已更新
Druck DPI 705E 系列手持式压力和可选温度指示仪具有坚固耐用的设计，并且测量精准、稳定可靠。

DPI 705E 系列紧凑、坚固，为单手操作而设计， 不仅可用于日常维护， 可以用于系统故障排除。

Safe area pressure indicator Hazardous area pressure indicator DPI 705E Series Druck Handheld Pressure Indicators The Druck DPI 705E Series of handheld pressure ａnd optional temperature indicators combine tough ａnd rugged design with accurate ａnd reliable measurements. Compact ａnd robust, the DPI 705E Series is designed for single handed operation ａnd provides many essential features required for routine maintenance ａnd system troubleshooting. Features • 41 pressure ranges from ±25 mbar to 1,400 bar (±10 inH20 to 20,000 psi/2.5 kPa to 140 MPa) • Total 1 year uncertainty down to 0.025% full scale (FS) over temperature range of -10°C to +50°C • Integral calibration record with calibration due count-down display • Rugged, handheld design with backlit high-contrast display • Leak test, tare, maximum/minimum ａnd filter functions • Hazardous Area (Intrinsically safe) version available • Optional remote plug ａnd play pressure (PM700E) ａnd Resistance Temperature Detector (RTD-PROBE) sensors • Compatible with our pneumatic ａnd hydraulic hand pumps DPI 705E Improves test efficiency • Power on ａnd use. No warm up time required. • 20 pressure measurement units (See below) • 1, 3 or 5 minute leak test • Impact resistant, sealed to IP54 • Large digit high-contrast LCD with backlight • Optional carrying case with belt loop • Optional magnetic/loop hanging strap • Long battery life • Integral desk stand ａnd hanger • 3 Levels of accuracy Special features Pressure units mbar, bar, Pa, kPa, hPa, MPa, psi , lb/ft2, kgf/cm2, kgf/m2, mmHg(0°C), mHg(0°C), inHg 0, mmH2O, cmH2O, mH2O, inH2O (4°C, 20°C), ftH2O (4°C, 20°C) Calibration certificates • Supplied as standard in bar, psi ａnd kPa • Optional UKAS accredited calibration available Leak test Used to determine if there is a leak in the system by recording the pressure change over a fixed time. Leak test can also be used with the RTD sensor to record a temperature change over time. User defined 1, 3 or 5 minute leak test with live countdown timer. Maximum/minimum Captures both maximum ａnd minimum readings in peak-hold mode. Zero Zero pressure correction (gauge/differential sensors) Tare 0 to 100% FS temporary zero offset capability by subtracting the current reading from subsequent measurements. Filter Enables a filtered pressure reading by showing a rolling average of the last 10 measurements. Providing a more stable reading in a noisy measurement. Alarm User adjustable high ａnd low pressure alarms with visual (Bell Icon, Pressure Reading ａnd Backlight flash) ａnd audible warning for 60 seconds. Calibration Used in conjunction with the optional pneumatic or hydraulic hand pumps, the DPI 705E Series provides a simple, low-cost calibration solution. Battery • 4 x AA Alkaline/NiCd/NiMH cells • Ultra power efficient design, can be used for 8 Hours per day, 6 days per week for up to a year using a single set of batteries. Display 16mm digital height LCD with ±99999 readout Hazardous area approvals • ATEX, IECEx, CSA, CCOE, XPL, KCs, NEPSI, ECASEx (Ordering code ‘H1‘) • INMETRO (Ordering code ‘H2‘) • IS Class I, Groups A, B, C & D, T4 Ex ia; Class I, Zone 0, AEx/Ex ia IIC T4 Ga (-10°C ≤ Ta ≤ +50°C) to CSA Std. 157-92, UL 913 (7th Ed.), CAN/CSA-C22.2 No. 60079-0:2018, CAN/CSA-C22.2 No. 60079-11:2012, ANSI/UL 60079-0:2018 ａnd ANSI/UL 60079-11:2012. • Ex ia IIC T4 Ga (-10°C ≤ Ta ≤ +50°C) to ATEX IEC 60079-0:2017 ａnd EN 60079-11:2011 Pressure ranges DPI 705E Internal pressure sensors The DPI705E includes an internal Absolute, Gauge or Differential sensor. Available ranges as per table: Negative calibration option (OP1) (Gauge sensors) Full Scale Pressure Range Standard ａnd High Accuracy sensors Premium accuracy sensors 25 mbar to 1 bar/10 inH2O to 15 psi/100 kPa to 2.5 kPa Available down to negative Full Scale by default Not available 1 bar to 20 bar/15 psi to 300 psi/20 kPa to 2 MPa Available down to -1 bar g as option OP1 Available down to -1 bar g by default 35 bar to 200 bar/500 psi to 3000 psi/3.5 MPa to 20 MPa Not available – calibrated down to 0 bar g Not available – calibrated down to 0 bar g Note: All differentials calibrated down to negative Full Scale (limited to -1bar) PM 700E External remote pressure sensors Any number of remote sensors can be individually used with a single DPI705E as all sensors hold their own calibration data ａnd are supplied with a 2.9m (9.5 feet) cable. Available ranges as per table: PM700E (Gauge, Absolute) PM700E (Differential) DPI 705E Internal pressure sensor availability PM 700E External pressure sensor availability Type Internal (1) Standard Internal (2) High Internal (3) Premium Remote (1) Standard Remote (2) High Remote (3) Premium 25 mbar / 10 inH2O / 2.5 kPa G, L - - G, L - - 70 mbar / 1 psi / 7 kPa G, L - - G, L - - 200 mbar / 3 psi / 20 kPa G, L - - G, L - - 350 mbar / 5 psi / 35 kPa G, A, L G, L - G, A, L G, L - 700 mbar / 10 psi / 70 kPa G, A, L G, L - G, A, L G, L - 1 bar / 15 psi / 100 kPa G, A, L G, A, L - G, A, L G, A, L - 750-1150 mbar / 11-17 psi /75-115 kPa (Barometric) B B - B B - 2 bar / 30 psi / 200 kPa G, A, L G, A, L G,L G, A, L G, A, L G,L 3.5 bar / 50 psi / 350 kPa G, A G, A G G, A G, A G 7 bar / 100 psi / 700 kPa G, A G, A G G, A G, A G 10 bar / 150 psi / 1000 kPa G, A G, A G, A G, A G, A G, A 20 bar / 300 psi / 2 MPa G, A G, A G, A G, A G, A G, A 35 bar / 500 psi / 3.5 MPa G, A G, A G, A G, A G, A G, A 70 bar / 1000 psi / 7 MPa G, A G, A G, A G, A G, A G, A 100 bar / 1500 psi / 10 MPa G, A G, A G, A G, A G, A G, A 135 bar / 2000 psi / 13.5 MPa G, A G, A G, A G, A G, A G, A 200 bar / 3000 psi / 20 MPa G, A G, A G, A G, A G, A G, A 350 bar / 5000 psi / 35 MPa A A A A A A 700 bar / 10000 psi / 70 MPa A A A A A A 1000 bar/ 15000 psi/ 100 MPa - - - A A A 1400 bar / 20000 psi / 140 MPa - - - A A A G = Gauge L = Differential A = Absolute B = Baro Accuracy levels 1-Standard ±0.1% FS Total accuracy over -10 to 50 degrees C including NLH&R,1 year drift ａnd calibration uncertainty 2-High ±0.05% FS Total accuracy over -10 to 50 degrees C including NLH&R,1 year drift ａnd calibration uncertainty 3-Premium ±0.025% FS Total accuracy over -10 to 50 degrees C including NLH&R,1 year drift ａnd calibration uncertainty Accuracy specification Gauge/differential sensors Standard accuracy High accuracy Premium accuracy Pressure range NLH&R Total uncertainty NLH&R Total uncertainty NLH&R Total uncertainty -10 to 50°C (14 to 122°F) (% FS) (% FS) (% FS) (% FS) (% FS) (% FS) 25 mbar 0.3 0.348 N/A N/A N/A N/A 70 mbar 0.1 0.121 N/A N/A N/A N/A 200 mbar 0.08 0.1 N/A N/A N/A N/A 350 mbar to 1 bar 0.08 0.1 0.04 0.05 N/A N/A 2 bar to 200 bar 0.08 0.1 0.04 0.05 0.018 0.025 Absolute sensors Standard accuracy High accuracy Premium accuracy Pressure range NLH&R Total uncertainty NLH&R Total uncertainty NLH&R Total uncertainty -10 to 50°C (14 to 122°F) (% FS) (% FS) (% FS) (% FS) (% FS) (% FS) 750 - 1150 mbar (Barometric) 0.08 0.1 0.04 0.075 N/A N/A 350 mbar ａnd 700 mbar 0.08 0.1 N/A N/A N/A N/A 1 bar to 7 bar 0.08 0.1 0.04 0.075 N/A N/A 10 bar to 1400 bar 0.08 0.1 0.04 0.075 0.018 0.063 Notes: 1. NLH&R Non-linearity, hysteresis ａnd repeatability. 2. Total uncertainty includes 1 year drift ａnd calibration uncertainty. For 350mbar to 7bar absolute ranges typical values are stated – for maximum values add 0.045%FS for standard accuracy, 0.055%FS for high accuracy. For 10bar absolute ranges ａnd above maximum values are stated above. Plug ａnd play remote sensor range DPI705E DPI705E-IS PM700E-CABLE (2.9m) PM700E-CABLE (2.9m) PM700E/PM700E-IS Differential IO-RTD-M12EXT (2m) Low & Medium Pressure High Pressure RTD-INTERFACE-485 RTD-INTERFACE-IS IO-RTD-PRB150 (150x6mm PT100 Probe) Media compatibility Sensors up to ａnd including 3.5bar (including differential) are exposed, 7-1400bar are diaphragm isolated. Pressure fittings Internal ａnd remote sensors are fitted with pressure connectors as detailed below: • P1 - G1/8 Female direct sensor connection of instrument, welded non-removable (for ranges 200 bar ａnd below) with optional adaptor: • P2 - G1/4 Female adaptor that goes into the instruments G1/8 female • P3 - 1/8 NPT Female adaptor that goes into the instruments G1/8 female • P4 - 1/4 NPT Female adaptor that goes into the instruments G1/8 female • P5 - Quick-Fit adaptor comes with G1/8 ａnd 1/8 NPT adaptors • P6 - 9/16 x 18 UNF Male direct sensor connection of instrument, welded non-removable (mandatory for ranges greater than/equal to 350 bar) Differential reference port: Legris 4 mm tubing adaptor. Adaptors The Legris adaptor fitted to the reference port can be removed using a 2.5mm hex key leaving a G1/8 female thread ａnd an M5 female thread. Pressure FS Media compatibility 0 to 3.5 bar Non-condensing dry gases compatible with 316L Stainless Steel, Pyrex, Silicon, Gold, Aluminium, Glass, Silicon Dioxide ａnd RTV Adhesive. Differential sensor reference port Non-condensing dry gases compatible with 316L ａnd 304 Stainless Steel, Pyrex, Silicon, Glass, Silicon Dioxide ａnd RTV Adhesive. 7 to 200 bar 316L Stainless Steel ａnd Hastelloy C276 350 to 1400 bar Inconel 625 ａnd 17-4PH Stainless Steel Note: Only fluids that are compatible as per above table should be used, to ensure the integrity of the pressure sensor. DPI705E General specifications Working pressure 110% FS (alarm active beyond this range) Sealing IP54 Operating temperature -10 to 50°C (14 to 122°F) Storage temperature -20 to 70°C (-4 to 158°F) Humidity 0 to 90% RH non condensing Shock ａnd vibration MIL-PRF-28800F for Class II equipment. 1 m Drop Tested @ -20°C (-4°F) EMC BS EN 61326-1 Electrical safety BS EN 61010-1 UL 61010-1 Pressure safety Pressure equipment directive class SEP. UL61010 Safe to 2xFS Approval CE marked, RCM Size ａnd weight L 200 mm, W 95 mm, D 43 mm 563 g maximum RoHS Compliant Resolution 5 digits G 1/8 female thread Legris adaptor Legris port for 4 mm OD tubing 4 mm tubing port 2.5 mm hex G 1/8 female thread M5 female thread G 1/8 female thread Optional remote RTD temperature interface/probe Enabling users to perform plug ａnd play temperature measurement capability, displaying units as resistance or temperature. The Interface only option P/N RTD-INTERFACE-485 for DPI705E Safe Area or P/N RTD-INTERFACE-IS for DPI705EIS Hazardous Area certification allows users to use their own PT100 RTD probe. RTDINTERFACE is supplied with a field-rewireable M12 connector to allow users to connect their own wire-ended RTD’s. The probe option P/N RTD-PROBE-485 for DPI705E Safe Area or P/N RTD-PROBE-IS for DPI705EIS Hazardous Area comes with the interface ａnd a 15 cm (6”) class A PT100 probe. All RTD-PROBExxx ａnd RTD-INTERFACE-xxx come with a 2.9m cable. For further options please see Accessories section. RTD Accuracy specification NLH&R ±1°C (2°F) for 24 hrs (note 1) Total Uncertainty 10° to 30°C (50° to 86°F) for 1 year (note 2) Additional error -10° to 10°C (14° to 50°F) 30° to 50°C (86° to 122°F) 0 to 400 Ω 0.012% Rdg + 0.005% FS 0.015% Rdg + 0.006% FS 0.001% FS/°C Pt 100 - Measured temp range -200 to 0°C 0.017% Rdg + 0.1°C Excluding PT100 calibration error Pt 100 - Measured temp range 0 to 850°C 0.0215% Rdg + 0.1°C Excluding PT100 calibration error Notes: 1. NLH&R includes stability at ±2°C for 24 hours, at temperatures within 10°C to 30°C. 2. Total uncertainty includes 1 year drift RTD General specifications Measuring temperatures IO-RTD-PRB150 -50°C to 200°C (when used with appropriate extension cable) RTD-INTERFACE (BODY) -10°C to 50°C RTD-PROBE -10°C to 50°C when directly plugged in to RTD-INTERFACE -25°C to 75°C when using supplied cable SPECIALIST RTD PROBES (Not supplied by Druck) The capability of the RTD-INTERFACE (resistance range) with a suitable extension cable ａnd suitable probe is 0 to 400Ω which equates to -250°C to +650°C for a PT100 probe. Dimensions IO-RTD-PRB150 RTD-PROBE Probe tip: Ø6.35 x 150mm Probe total: Ø15 x 200mm RTD-INTERFACE Body: Ø34 x 72mm length Ordering information for DPI705E handheld pressure indicator The DPI 705E ａnd DPI 705E-IS are supplied with a user guide ａnd calibration certificate as standard. Model type DPI705E Safe Area pressure indicator DPI705EIS Hazardous Area pressure indicator Accuracy (Now offering three levels of accuracy – see page 3 for availability by pressure range) 1 Standard 2 High 3 Premium Pressure range ａnd reference type; (Mandatory to ｓelect only one e.g. 008A for each configuration) Gauge (G) Absolute (A) Differential (L) Barometric (B) 25 mbar/10 inH2O/2.5 kPa 008G - 008L - 70 mbar/1 psi/7 kPa 01G - 01L - 200 mbar/3 psi/20 kPa 02G - 02L - 350 mbar/5 psi/35 kPa 03G 03A 03L - 700 mbar/10 psi/70 kPa 04G 04A 04L - 1 bar/15 psi/100 kPa 05G 05A 05L - 750-1150 mbar/11-17 psi/ - - - 05B 75-115 kPa (Barometric) 2 bar/30 psi/200 kPa 07G 07A 07L - 3.5 bar/50 psi/350 kPa 08G 08A - - 7 bar/100 psi/700 kPa 10G 10A - - 10 bar/150 psi/1000 kPa 11G 11A - - 20 bar/300 psi/2 MPa 13G 13A - - 35 bar/500 psi/3.5 MPa 14G 14A - - 70 bar/1000 psi/7 MPa 16G 16A - - 100 bar/1500 psi/10 MPa 165G 165A - - 135 bar/2000 psi/13.5 MPa 17G 17A - - 200 bar/3000 psi/20 MPa18G 18A - - 350 bar/5000 psi/35 MPa - 20A - - 700 bar/10000 psi/70 MPa - 22A - - Pressure fitting - Refer to page 5 P1 G1/8 Female For ranges less than 350 bar (welded non-removable) P2 G1/4 Female adaptor For ranges less than 350 bar P3 1/8 NPT Female adaptor For ranges less than 350 bar P4 1/4 NPT Female adaptor For ranges less than 350 bar P5 Quick-Fit adaptor For ranges less than 350 bar P6 9/16 x 18 UNF Male Mandatory for ranges greater than/equal to 350 bar (welded non-removable) Hazardous area approvals (Mandatory to ｓelect one) H0 No hazardous area approval (Default if DPI705E selected) H1 ATEX, IECEx, CSA, CCOE, XPL, KCS, NEPSI, ECASEx H2 INMETRO (Brazil) Pressure units U0 All Pressure units (Default selection) U1 Pa (Si) Pressure units only Options (Mandatory to ｓelect one) OP0 No option required OP1 Negative calibration for gauge ranges 20 bar ａnd below DPI705EIS - 1 – 07G – P2 - H1 - U0 - OP1 (Example model numbers) Ordering information for PM700E external remote pressure sensors The PM 700E ａnd PM 700E-IS are supplied with a user guide ａnd calibration certificate as standard. Model type PM700E Safe Area External remote pressure sensorr PM700EIS Hazardous Area External remote pressure sensor Accuracy (Now offering three levels of accuracy – see page 3 for availability by pressure range) 1 Standard 2 High 3 Premium Pressure range ａnd reference type; (Mandatory to ｓelect only one e.g. 008A for each configuration) Gauge (G) Absolute (A) Differential (L) Barometric (B) 25 mbar/10 inH2O/2.5 kPa 008G - 008L - 70 mbar/1 psi/7 kPa 01G - 01L - 200 mbar/3 psi/20 kPa 02G - 02L - 350 mbar/5 psi/35 kPa 03G 03A 03L - 700 mbar/10 psi/70 kPa 04G 04A 04L - 1 bar/15 psi/100 kPa 05G 05A 05L - 750-1150 mbar/11-17 psi/ - - - 05B 75-115 kPa (Barometric) 2 bar/30 psi/200 kPa 07G 07A 07L - 3.5 bar/50 psi/350 kPa 08G 08A - - 7 bar/100 psi/700 kPa 10G 10A - - 10 bar/150 psi/1000 kPa 11G 11A - - 20 bar/300 psi/2 MPa 13G 13A - - 35 bar/500 psi/3.5 MPa 14G 14A - - 70 bar/1000 psi/7 MPa 16G 16A - - 100 bar/1500 psi/10 MPa 165G 165A - - 135 bar/2000 psi/13.5 MPa 17G 17A - - 200 bar/3000 psi/20 MPa 18G 18A - - 350 bar/5000 psi/35 MPa - 20A - - 700 bar/10000 psi/70 MPa - 22A - - 1000 bar/ 15000 psi/ 100 MPa - 23A - - 1400 bar/20000 psi/140 MPa - 24A - - Pressure fitting - Refer to page 5 P1 G1/8 Female For ranges less than 350 bar (welded non-removable) P2 G1/4 Female adaptor For ranges less than 350 bar P3 1/8 NPT Female adaptor For ranges less than 350 bar P4 1/4 NPT Female adaptor For ranges less than 350 bar P5 Quick-Fit adaptor For ranges less than 350 bar P6 9/16 x 18 UNF Male Mandatory for ranges greater than/equal to 350 bar (welded non-removable) Hazardous area approvals (Mandatory to ｓelect one) H0 No hazardous area approval (Default if DPI705E selected) H1 ATEX, IECEx, CSA, CCOE, XPL, KCS, NEPSI, ECASEx H2 INMETRO (Brazil) Options (Mandatory to ｓelect one) OP0 No option required OP1 Negative calibration for gauge ranges 20 bar ａnd below PM700E - 1 – 07G – P2 - H0 - OP1 (Example model numbers) Options OP1 - Negative calibration Optionally available for Gauge ranges of 20 bar ａnd below (default for -3 accuracy). If this option is chosen, then the calibration certificate will include values down to -1 bar g. UKAS calibration We also offer UKAS accredited calibrations, please advise at the time of order placement if required. Accessories Please state any accessories required as separate items when placing order. The DPI 705E Safe ａnd Hazardous area versions are compatible with the following accessories unless otherwise specified. Part code Description IO705E-CASE DPI705 & DPI705E Carry Case IO705E-CASE-IS DPI705 & DPI705E Carry Case (IS) IO705E-STRAP DPI705E Hanging Strap PM700E-CABLE PM700E Remote Sensor Cable 2.9m (Cable from DPI705E to PM700E or RTD-INTERFACE) IO-ADAPT-G1/4 Adaptor G1/8 Male to G1/4 Female IO-ADAPT-1/4NPT Adaptor G1/8 Male to 1/4NPT Female IO-ADAPT-1/8NPT Adaptor G1/8 Male to 1/8NPT Female IO-ADAPT-QF G1/8M to Quick-fit Adaptor 182-190 Adaptor High Pressure 9/16UNF Female to 3/8BSP Male (suitable for Pressure Fitting option P5 up 1000 bar) RTD-INTERFACE-485 RTD Interface only - RS485 RTD-INTERFACE-IS RTD IS Interface only - RS485 RTD-PROBE-485 RTD Interface with PT100 probe - RS485 (supplied with 2.9m cable) RTD-PROBE-IS RTD IS Interface with PT100 probe-RS485 (supplied with 2.9m cable) IO-RTD-M12CON Field Wireable M12 connector 4-pin IO-RTD-M12EXT M12M to M12F 2m ext lead (6.5 ft) 4-wire (Cable interface to the PT100 probe) IO-RTD-PRB150 RTD Probe 150mm, PT100 steel Class A IOHOSE-NP1 20 bar Hose Assembly 1 metre IOHOSE-NP2 20 bar Hose Assembly 2 metre IO620-HOSE-P1 Pneumatic Hose 1 metre IO620-HOSE-P2 Pneumatic Hose 2 metres IO620-HOSE-P3 Pneumatic Hose 3 metres IO620-HOSE-H1 Hydraulic Hose 1 metre IO620-HOSE-H2 Hydraulic Hose 2 metres IO620-HOSE-H3 Hydraulic Hose 3 metres IO620-HOSE-P1-IS Pneumatic Hose 1 metre (IS) IO620-HOSE-P2-IS Pneumatic Hose 2 metres (IS) IO620-HOSE-P3-IS Pneumatic Hose 3 metres (IS) IO620-HOSE-H1-IS Hydraulic Hose 1 metre (IS) IO620-HOSE-H2-IS Hydraulic Hose 2 metres (IS) IO620-HOSE-H3-IS Hydraulic Hose 3 metres (IS) IO620-BSP Pressure Adaptor Set - BSP IO620-NPT Pressure Adaptor Set - NPT Related products Process calibrators Druck offer a comprehensive range of portable pressure, temperature ａnd electrical field calibrators. To help you ｓelect the right process calibration tools we have categorised our products into three ranges. Druck’s Essential range provides rugged, accurate ａnd easy-to-use test ａnd calibration tools. Druck’s Expert range introduces higher accuracy ａnd increased functionality. Druck’s Elite range provides a modular system offering stateof-the-art multifunction communication ａnd calibration. Pneumatic ａnd hydraulic test kits: PV210 Low pressure pneumatic hand pump Fully portable, easy to use, an ideal tool for low pressure calibration checks on pressure transmitters, pressure switches, indicators, recorders ａnd controllers. • Generates pressures to 3 bar (45 psi) • Generates vacuum to 90%. PV211 Pneumatic hand pump Lightweight, high quality combined pressure ａnd vacuum hand pump, designed to provide maximum pneumatic pressures efficiently ａnd effortlessly. • Pneumatic pressures in excess of 40 bar (600 psi) • Generates vacuum to 96% PV212 High pressure hydraulic hand pump Lightweight, easy to use, an ideal tool for calibrating pressure transmitters, pressure transducers, pressure switches ａnd pressure gauges. • Generates pressures up to 1000 bar (15,000 psi) • Controlled pressure release ａnd adjustment PV411A Multifunction hand pump High quality field proven pressure ａnd vacuum hand pump. This product replaces four conventional hand pumps. • Pneumatic pressures to 40 bar (600 psi) • Hydraulic pressures to 700 bar (10,000 psi) • Removable hydraulic reservoir which can be disconnected from the pump without draining the fluid • Excellent low pressure control • 95% vacuum Laboratory ａnd workshop instruments Druck’s PACE Series offers a comprehensive range of pressure controllers ａnd indicators. Pressure transducers ａnd transmitters Druck offer a wide range of pressure transducers ａnd transmitters including analog, digital ａnd HART/Smart devices. Please contact BH for further information Supporting services Druck’s highly trained staff can support you, no matter where you are in the world. We can provide nationally accredited calibration (both initially ａnd at periodic intervals), extended warranty terms, maintenance ａnd even rental of portable or laboratory instruments. Please contact your local Druck customer care team for more information. druck.com Copyright 2022 Baker Hughes Company. All rights reserved. 920-697E BHC39124 (02/2022)

更新时间：2024/3/19 13:38:53